Semiconductor
Regulador 2.5-36v Adjustable Shunt Volta
PACK OF 2500 PIECES The TL431 series programmable shunt Voltage Reference with guaranteed temperature stability over the entire operating temperature range. The output voltage can be set to any value between 2.5 and 36V with two external resistors. The TL431 and TL432 operate with a wide current range from 1 to 100mA with a typical dynamic impedance of 0.22Ω. -100 to +150mA Continuous cathode current range VOLTAGE REF, SHUNT, 2.495V-36V, TO-226AA; Voltage Reference Type: Shunt - Adjustable; Product Range: -; Reference Voltage: 2.495V to 36V; Initial Accuracy: 2%; Temperature Coefficient: -; Voltage Reference Case Style: TO-92; No. of Pins: 3Pins; Operating Temperature Min: 0°C; Operating Temperature Max: 70°C; Automotive Qualification Standard: -; MSL: -; SVHC: No SVHC (17-Dec-2015); IC Generic Number: 431; IC Temperature Range: Commercial; Input Voltage Max: 36V; Input Voltage Min: 3V; Operating Temperature Range: 0°C to +70°C; Reference Volt Tolerance ±%: 1%; Reference Volts: 2.495V; Topology: Shunt, Programmable Applications Power Management, Industrial, Automotive
$162.00
Regulador De Tensión Lineal 3.3v 0.1a Po
PACK OF 2500 PIECES L78L33ABUTR is a L78L series, three-terminal positive voltage regulator. It employs internal current limiting and thermal shutdown, making it essentially indestructible. If adequate heat-sink is provided, it can deliver up to 100mA output current. It is intended as a fixed voltage regulator in a wide range of applications including local or on-card regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, it can be used with power pass elements to make high-current voltage regulators. The L78L series used as a zener diode/resistor combination replacement offers improvement along with lower quiescent current and lower noise. Short-circuit protection No external components are required Output voltage is 3.3V typical (TJ = 25°C) Quiescent current is 6mA maximum (TJ = 25°C) Output noise voltage is 40µV typical (B = 10Hz to 100KHz, TJ = 25°C) Supply voltage rejection is 49dB typical (VI = 6.3 to 16.3 V, f = 120Hz, IO = 40mA, TJ = 25°C) Operating junction temperature range from -40 to 125°C SOT-89 package Outputs = 1 / Fixed Output Voltage V = 3.3 / Output Voltage Min. V = 3.1 / Output Voltage Max. V = 3.5 / Dropout Voltage V = 2 / Output Current mA = 100 / Load Regulation mV = 60 / Line Regulation mV = 150 / Supply Voltage Max. V = 30 / Operating Temperature Min. °C = 0 / Operating Temperature Max. °C = 125 / Package Type = SOT-89 / Pins = 4 / Mounting Type = SMD / MSL = Level-1 / Packaging = Tape & Reel / Length mm = 4.6 / Width mm = 4.3 / Height mm = 1.6 / Reflow Temperature Max. °C = 260
$324.00
C. Integrado 8 Digit Pdip 18
PACK OF 20 PIECES The ULN2803AN is a Darlington Transistor Array. It is a high-voltage, high-current Darlington transistor array that can be used to drive a variety of loads. It is designed to provide a low-cost, easy-to-use solution for driving high-current loads from low-voltage logic circuits.Features• High-voltage, high-current Darlington transistor array• Low-cost, easy-to-use solution for driving high-current loads from low-voltage logic circuits• Eight NPN Darlington pairs with common emitters• Output current of 500mA (single output)• Output voltage of 50V• Inputs compatible with TTL and CMOS logic• Internal clamp diodes for inductive loads• High-noise immunityApplicationThe ULN2803AN is suitable for a wide range of applications, including motor control, relay drivers, lamp drivers, and other high-current loads. It is also suitable for use in automotive, industrial, and consumer applications. Transistor Polarity:NPN; Transistors, No. of:8; Collector-to-Emitter Breakdown Voltage:50V; Current Ic Continuous a Max:0.5A; Termination Type:SMD; Case Style:DIP; No. of Pins:18; Operating Temperature Range:-40°C to +85°C; Base Number:2803; IC Generic Number:2803; Logic Function Number:2803; Max Output Current:500mA; Output Type:Open Collector; Transistor Type:Power Darlington; Voltage, Input Max:5V; Voltage, Output Max:50V
$10.80
Audio Power Amplifier, AB, 1 Channels, 4V to 12V, DIP, 8 Pins
The LM386N-1/NOPB is a low voltage class AB audio power amplifier in 8 pin DIP package. This power amplifier is designed for use in low voltage applications. The gain is internally set to 20 to keep external part count low. The addition of an external resistor and capacitor between pins 1 and 8 will increase the gain to any value from 20 to 200. The inputs are ground referenced while output automatically biases to one half cycle of supply voltage. The quiescent power drain is only 24mW when operating from 6V supply making LM386 ideal for battery operation. Minimum external parts Wide supply voltage range from 4V to 12V Low quiescent current drain of 4mA Self centring output quiescent voltage Low distortion of 0.2% Operating temperature range 0°C to 70°C Output power is 325mW at VS=6V and RL=8W Voltage gain is 26db at VS=6V and f=1KHz Bandwidth (BW) of 300KHz Power supply rejection ratio (PSRR) is 50dB Applications: Audio, Portable Devices, Consumer Electronics, Power Management, Signal Processing
$0.00
LM317 Series 1.5 A 1.2 to 37 V Adjustable Positive Voltage Regulator - TO-220
PACK OF 50 PIECES The LM317T is a monolithic integrated circuit, positive adjustable voltage regulator. It is designed to supply more than 1.5 A of load current with an output voltage adjustable over a 1.2 V to 37 V range. The nominal output voltage is selected by means of only a resistive divider, making the device exceptionally easy to use and eliminating the stocking of many fixed regulators. Features: Output voltage range: 1.2 V to 37 VOutput current in excess of 1.5 A0.1 % line and load regulationFloating operation for high voltagesComplete series of protectionscurrent limiting, thermal shutdown and SOA control
$16.74
Standard Regulator Pos 12V 0.1A 3-Pin TO-92 Ammo
PACK OF 100 PIECES The L78L series of three-terminal positive regulators employ internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 mA output current. They are intended as fixed voltage regulators in a wide range of applications including local or on-card regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power pass elements to make high-current voltage regulators. The L78L series used as Zener diode/resistor combination replacement, offers e improvement along with lower quiescent current and lower noise. Key Features Output current up to 100 mA Output voltages of 3.3; 5; 6; 8; 9; 10; 12; 15; 18; 24 V thermal overload protection Short-circuit protection No external components are required Available in either ± 4% (A) or ± 8% (C) selection
$20.52
Linear Voltage Regulator, 7808, Fixed, 14V To 30V In, 8V And 0.1A Out, TO-92-3
PACK OF 100 PIECES The L78L08ACZ is a 3-terminal Positive Regulator with 8V output voltage. It employs internal current limiting and thermal shutdown, making it essentially indestructible. If adequate heat-sink is provided, it can deliver up to 100mA output current. It is intended as fixed voltage regulators in a wide range of applications including local or on-card regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, it can be used with power pass elements to make high-current voltage regulators. The device used as Zener diode/resistor combination replacement, offers e improvement along with lower quiescent current and lower noise.No external components are requiredShort-circuit protection Applications: Power Management, IndustrialWarningsMarket demand for this product has caused an extension in leadtimes. Delivery dates may fluctuate. Product exempt from discounts.
$20.52
L78L Series 100 mA 5 V Three Terminal Positive Voltage LDO Regulator - TO-92
PACK OF 2000 PIECES The L78L05ACZTR is of three-terminal positive regulators employ internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 mA output current.They are intended as fixed voltage regulators in a wide range of applications including local or oncard regulation for elimination of noise and distribution problems associated with single-point regulation. Features: Output current up to 100 mAOutput voltages of 3.3; 5; 6; 8; 9; 10; 12; 15; 18; 24 VThermal overload protectionShort circuit protectionNo external components are requiredAvailable in either ± 5% (AC) or ± 10% (C) selection
$345.60
Fixed Positive Standard Regulator, 12V, BIPolar, PSSO2
PACK OF 50 PIECES The L7812CV is a voltage regulator integrated circuit (IC) in the L78 series. It's designed to provide a fixed positive output voltage of 12 volts with a maximum output current of up to 1.5 amperes. This IC is widely used in various electronic applications for providing a stable 12V supply from a higher voltage source. The "CV" suffix typically indicates a standard package type, which in this case is a TO-220 package, known for its ability to handle higher power dissipation.Key features of the L7812CV include thermal overload protection and short-circuit protection, ensuring the stability and reliability of the device under various conditions. Its ability to provide a stable output voltage despite fluctuations in the input voltage or load conditions makes it a popular choice in power supply design for consumer electronics, computer hardware, and other electronic projects.
$12.96
L7809 Series 1.5 A 9 V Three Terminal Positive Voltage Regulator - TO-220
PACK OF 50 PIECES The L7809CV is a three-terminal positive regulators is available in TO-220, TO-220FP, TO-3, D²PAK and DPAK packages and several fixed output voltages, making it useful in a wide range of applications. These regulators can provide local on-card regulation, eliminating the distribution problems associated with single point regulation. Each type employs internal current limiting, thermal shut-down and safe area protection, making it essentially indestructible.If adequate heat sinking is provided, they can deliver over 1 A output current. Although designed primarily as fixed voltage regulators, these devices can be used with external components to obtain adjustable voltage and currents. Features: Output current up to 1.5 AOutput voltages of 5, 6, 8, 8.5, 9, 12, 15, 18, 24 VThermal overload protectionShort circuit protectionOutput transition SOA protection2 % output voltage tolerance (A version)Guaranteed in extended temperature range (A version)
$15.66
L7805 Series 5 V 1.5 A Fixed Flange Mount Voltage Regulator - TO-220-3
PACK OF 50 PIECES Linear regulators are Step-Down regulators only. There are 2 types of regulators, Shunt and series-pass regulators.For IC linear voltage regulators, the regulator type determines the configuration of the pass device as well as the dropout voltage. Standard voltage regulators use an NPN Darlington configuration and have a dropout voltage between 1.5V and 2.2 V. Low dropout (LDO) regulators differ from standard regulators in that the pass device consists of a single PNP transistorLinear regulators provide significant advantages over switching regulators in simplicity, cost, and output noise.The only difference between a 'normal' linear regulator and a LDO one is that, the LDO type can have a lower constant voltage-drop across the series-pass element.The L78xx series of three-terminal positive regulators is available in TO-220, TO-220FP, TO-3, D2PAK and DPAK packages and several fixed output voltages, making it useful in a wide range of applications. These regulators can provide local on-card regulation, eliminating the distribution problems associated with single point regulation. Each type employs internal current limiting, thermal shut-down and safe area protection, making it essentially indestructible. If adequate heat sinking is provided, they can deliver over 1 A output current. Although designed primarily as fixed voltage regulators, these devices can be used with external components to obtain adjustable voltage and currents.The ST Micro L7805ACV is a 5 volt positive linear regulator. It has 1 amperage, a 4% tolerance, commercial temperature, and comes in a TO-220 package.
$12.96
L7805 Bulk Through Hole Over Temperature Short Circuit voltage regulator linear 2V 8.7mm 1.5A 0C~125C
PACK OF 50 PIECES The Liner regulator IC is packaged in TO-204AA, TO-3 case. On the Linear IC itself, there are 3 terminations. Fixed is the output type of the Voltage Regulator IC. As part of this electrical component, 1 regulators are implemented. Variations are made to the Through Hole operating temperature range by the Voltage Regulator IC. Default settings are set to 0°C~125°C degrees. There is a Positive configured as the output function for this IC regulator. There are a total of 2 pins on this board. There are 1 outputs total on this voltage regulator IC in order to ensure that prompt and sufficient performance is achieved. There is a dropout voltage of 10 volts on this IC regulator. Chips have 3 pins. For your information, the basic part number for this regulator IC is L7805. In order to meet the operation requirements, its maximal output current reaches 1.5A. It operates in the 8mA Quiescent Current state. This IC regulator has a tolerance of 5%, which is quite low.L7805CT Features2V dropout voltage5% tolerance Applications: Battery-powered deviceCommunication devicePersonal communication devicePortable telephoneElectronic notebookCameraVideo equipmentCPU power supplySwitching regulatorMultiple-power supply system
$12.96
TC1185 Series 150 mA 3 V Fixed Output CMOS LDO Regulator w/ Shutdown - SOT-23-5
PACK OF 100 PIECES The TC1185-3.0VCT713 is a 3 V 150 mA CMOS Low Dropout Regulator with Shutdown and VREF Bypass, available in SOT-23-5 package. It is designed specifically for battery-operated systems, the devices’ CMOS construction eliminates wasted ground current, significantly extending battery life. Features: Low Supply Current (50 μA, typical) Low Dropout Voltage High Output Voltage Accuracy Standard or Custom Output Voltages Power-Saving Shutdown Mode Reference Bypass Input for Ultra Low-Noise Operation Overcurrent and Overtemperature Protection Space-Saving 5-Pin SOT-23 Package Pin-Compatible Upgrades for Bipolar Regulators Standard Output Voltage Options:1.8V, 2.5V, 2.6V, 2.7V, 2.8V, 2.85V, 3.0V, 3.3V, 3.6V, 4.0V, 5.0 Applications: Battery Operated Systems Portable Computers Medical Instruments Instrumentation Cellular/GSM/PHS Phones Linear Post-Regulators for SMPS Pagers
$64.80
RN42 Series 3.6 V 2.4 GHz 4 dBm Class 2 Bluetooth® Module with EDR Support
PACK OF 70 PIECES The RN42-I/RM is a small form factor, low power, class 2 Bluetooth radio module offering high performance and easy integration for designers looking to add wireless capability to their products. It is designed by Microchip Technology and is one of the professional series Bluetooth modules in their product line. Here are some of the key features and specifications for the RN42-I/RM: Bluetooth Technology: It is based on Bluetooth 2.1 + EDR (Enhanced Data Rate) standard, offering a secure and stable wireless communication protocol. Class 2 Module: As a Class 2 Bluetooth module, it provides a standard communication range of up to 30 feet (10 meters). Low Power Consumption: The module is optimized for low power consumption, making it suitable for battery-powered applications. Easy Integration: The RN42-I/RM supports multiple interface protocols, including UART, SPI, and I2C, allowing for straightforward integration with microcontrollers and other digital systems. High Data Rates: It can support data rates up to 3 Mbps, enabling high-speed wireless data transfer. Profiles and Protocols: The module comes with built-in support for multiple Bluetooth profiles such as SPP (Serial Port Profile) and can be configured to support others as required. Compact Size: With its small footprint, the module can be easily fitted into space-constrained applications. Robust Firmware: It is equipped with robust firmware that simplifies configuration and enhances functionality, often allowing for the module to be used with simple AT commands for setup. Certifications: The RN42-I/RM is typically certified for FCC, CE, and other regulatory approvals, reducing the compliance burden for product developers. Versatility: It is designed for a wide range of applications in the medical, industrial, automotive, and consumer markets where reliable wireless communication is essential. Developers often choose the RN42-I/RM for its mix of high performance, ease of use, and flexibility, making it a go-to component for adding Bluetooth connectivity to a diverse array of electronic products.
$2,101.68
Microcontroller, 28-SPDIP, 64KB Flash, 8192 Bytes RAM, 16 MIPS
COST PER PIECE The PIC24FJ64GA002-I is a high-performance microcontroller packaged in a 28-pin SPDIP (Skinny Plastic Dual In-line Package). It features 64KB of flash memory, 8192 bytes of RAM, and is capable of executing up to 16 Million Instructions Per Second (16 MIPS). This microcontroller is well-suited for a wide range of applications requiring a balance between processing power, memory size, and physical compactness. Key Features and Benefits: 64KB Flash Memory: Provides ample space for program storage, making it suitable for complex applications that require large codebases or data storage. 8192 Bytes of RAM: Offers sufficient RAM for data processing and temporary data storage, facilitating smooth and efficient operation of applications. High-Speed Processing (16 MIPS): With a processing speed of up to 16 MIPS, this microcontroller can handle demanding tasks and execute instructions quickly, making it suitable for high-performance applications. 28-SPDIP Package: The 28-pin SPDIP format provides a convenient and compact package, ideal for breadboard prototyping and for use in space-constrained applications. Versatile Applications: This microcontroller can be used in a variety of applications, including automation systems, consumer electronics, robotics, and Internet of Things (IoT) devices. Model (PIC24FJ64GA002-I): The specific model number ensures easy identification and procurement, allowing designers and engineers to select the appropriate microcontroller for their projects. In summary, the PIC24FJ64GA002-I microcontroller, with its robust memory capacity, high-speed processing, and compact packaging, is a versatile and powerful solution for a wide range of advanced electronic applications. Its combination of performance and size makes it an excellent choice for both hobbyist and professional projects.
$5.64
MCU 8-bit PIC18 PIC RISC 64KB Flash 1.8V/2.5V/3.3V 64-Pin TQFP T/R
PACK OF 1200 PIECES Direct LCD Panel Drive Capability: Can drive LCD panel while in Sleep modeUp to 48 Segments and 192 Pixels, Software SelectableProgrammable LCD Timing module:Multiple LCD timing sources availableUp to four commons: static, 1/2, 1/3 or 1/4 multiplexStatic, 1/2 or 1/3 bias configurationOn-Chip LCD Boost Voltage Regulator for Contrast ControlCharge Time Measurement Unit (CTMU) for Capacitive Touch SensingADC for Resistive Touch Sensing10,000 Erase/Write Cycle Flash Program Memory, TypicalFlash Retention 20 Years, MinimumSelf-Programmable under Software ControlWord Write Capability for Flash Program Memory for Data EEPROM EmulatorsPriority Levels for Interrupts8 x 8 Single-Cycle Hardware MultiplierExtended Watchdog Timer (WDT):Programmable period from 4 ms to 131sIn-Circuit Serial Programming™ (ICSP™) via Two PinsIn-Circuit Debug via Two PinsOperating Voltage Range: 2.0V to 3.6V5.5V Tolerant Input (digital pins only)Selectable Open-Drain Configuration for Serial Communication and CCP Pins for Driving Outputs up to 5VOn-Chip 2.5V RegulatorTape and Reel Packaging Technical Attributes Description Value Device Core PIC IC Case / Package TQFP IC Mounting Surface Mount Interfaces I2C/SPI/USART No. of I/Os 51 No. of Pins 64 Operating Frequency Max 48 Operating Temperature Max 85 Operating Temperature Min -40 Program Memory Size 64 KB Supply Voltage Max 2.7 Supply Voltage Min 1.7
$6,298.56
8 Bit MCU, Flash, PIC18 Family PIC18F K5x Series Microcontrollers, PIC18, 48 MHz, 32 KB, 40 Pins
COST PER PIECE The PIC18F45K50-I/P is a high-performance PIC18 family 8-bit powerful (200 nanosecond instruction execution) yet easy-to-program CMOS flash based Microcontroller packs powerful PIC®(RISC) architecture with up to 16 MIPS of processing power with benchmark nanoWatt XLP extreme low power consumption. This product offer all of the advantages of the well recognized high-performance x16 architecture with standardized features including 32kB of addressable program memory size, 2048bytes of data memory size, 36 general-purpose I/O pins, two comparators, 25-channel 10-bit analog-to-digital (A/D) converter and one 5-bit digital-to-analog (D/A) converter. This device operates at a maximum frequency of 48MHz wide operating voltage of 1.8 to 5.5V. 83 (16-bit wide) powerful C-optimized 32 level hardware stack 1 (8-bit) file select register Integrated 8x8 hardware multiply Programmable brown-out reset (BOR) Programmable low voltage detection 16MHz internal oscillator Watch dog timer (WDT) Internal voltage reference (Bandgap) Charge time measurement unit (CTMU) Two 8-bit digital timers Two 16-bit digital timers 1x Enhanced Capture/Compare/PWM (ECCP) full-speed USB 2.0 25x Capacitive touch channels In-Circuit Serial Programming™ (ICSP™) 256bytes of EEPROM data memory Applications: Industrial, Automotive, Consumer Electronics, Motor Drive & Control, Lighting, Medical, Security Warnings: Market demand for this product has caused an extension in leadtimes. Delivery dates may fluctuate. Product exempt from discounts.
$5.16
8 Bit MCU, Flash, PIC18 Family PIC18F45xx Series Microcontrollers, PIC18, 48 MHz, 32 KB, 40 Pins
COST PER PIECE The PIC18F4550-I/P offers high computational performance with the addition of high endurance and enhanced flash program memory. In addition to these features, the PIC18F4550-I/P introduces design enhancements that make these microcontrollers a logical choice for many high performance, power sensitive applications. Full Speed USB 2.0 (12Mbit/s) interface 1K byte dual port RAM + 1K byte GP RAM Full speed transceiver 16 endpoints (IN/OUT) Streaming port Internal pull up resistors (D+/D-) 48MHz performance (12 MIPS) Applications: Automation & Process Control, Communications & Networking, Consumer Electronics, Embedded Design & Development, Multimedia, Portable Devices, Robotics, Sensing & Instrumentation, Security
$8.39
PIC18F Series 48 kB Flash 3968 B RAM 40 MHz 8-Bit Microcontroller - PDIP-40
COST PER PIECE Microchip’s 8-bit PIC microcontrollers fall into three product architecture categories providing a variety of options for any application requirement. The specific families include: Baseline – PIC10F and some PIC12F and PIC16F; Mid-Range PIC12F and PIC16F; and High Performance – PIC18F. All device families have low power capability, flexible Flash program memory, and separate instruction and data buses to enable single cycle execution. Features: CPU: Up to 10 MIPS performance C compiler optimized RISC architecture 8 x 8 Single Cycle Hardware Multiply System: Internal oscillator support - 31 kHz to 8 MHz, up to 32 MHz with 4X PLL Fail-Safe Clock Monitor – allows safe shutdown if clock fails Watchdog Timer with separate RC oscillator Wide operating Voltage range; 2.0 V to 5.5 V NanoWatt Power Managed Modes: Run, Idle and Sleep modes Idle mode currents down to 5.8 uA typical Sleep mode currents down to 0.1 uA typical Analog Features: 10-bit ADC, 13 channels 100K samples per second Programmable Low Voltage Detection Module Programmable Brown-out Reset module Two Analog comparators with input multiplexing EUSART module including LIN bus support Four Timer Modules Up to 5 PWM outputs Up to 2 Capture / Compare
$8.76
PIC18F Series 32 KB Flash 1.5 kB RAM 40 MHz 8-Bit Microcontroller - PDIP-40
COST PER PIECE Microchip provides solutions for the entire performance range of 8-bit, 16-bit, and 32-bit microcontrollers, with a powerful architecture, flexible memory technologies, comprehensive easy-to-use development tools, complete technical documentation and post design-in support through a global sales and distribution network. 16-bit PIC Microcontrollers & dsPIC Digital Signal Controllers. Microchip offers two 16-bit Microcontroller (MCU) families plus two 16-bit Digital Signal Controller (DSC) families that give you compatible options across a wide spectrum of price, performance and feature sets. Features: CPU: Up to 10 MIPS performance C compiler optimized RISC architecture 8 x 8 Single Cycle Hardware Multiply System: Internal oscillator support - 31 kHz to 8 MHz, up to 32 MHz with 4X PLL Fail-Safe Clock Monitor – allows safe shutdown if clock fails Watchdog Timer with separate RC oscillator Wide operating Voltage range; 2.0 V to 5.5 V NanoWatt Power Managed Modes: Run, Idle and Sleep modes Idle mode currents down to 5.8 uA typical Sleep mode currents down to 0.1 uA typical Analog Features: 10-bit ADC, 13 channels 100K samples per second Programmable Low Voltage Detection Module Programmable Brown-out Reset module Two Analog comparators with input multiplexing EUSART module including LIN bus support Four Timer Modules Up to 5 PWM outputs Up to 2 Capture / Compare
$7.78
PIC18F Series 64 KB Flash 3648 B RAM 64 MHz 8-Bit Microcontroller - SOIC-28.
COST PER PIECE The PIC18F26K80-I/SO is a 3648 B RAM 64 kB flash, high-performance 8-bit microcontroller. This device is ideal for applications requiring cost-effective, low-power CAN solutions with high performance and robust peripheral set in small package.It has low sleep current for low power applications and 1.8 V to 5.5 V operating voltage for automotive, building control, elevator control and industrial applications. Timers/enhanced compare/capture/PWMs for precision timing control, 12-bit ADC for advance analog interface. Features: 20 nA sleep mode300 nA watch dog timer operation in Sleep modesIntegrated ECAN conforming to CAN 2.0 B active specificationExtreme low power sleep mode ideal for battery applicationsCharge time measurement unit supports touch sensing and advanced sensing applications12-bit ADC
$5.12
PIC18F Series 64 kB Flash 3.8 KB RAM 64 MHz 8-Bit Microcontroller - SPDIP-28
COST PER PIECE The PIC18F26K22-I/SP is a low-power and high performance 8-bit Microcontroller with XLP Technology. Available in through hole SPDIP-28 package. Features: High Performance RISC CPU: C Compiler optimized architecture/instruction set Data EEPROM to 1024 bytes Linear program memory addressing to 64 Kbytes Linear data memory addressing to 4 Kbytes Up to 16 MIPS operation 16-bit wide instructions, 8-bit wide data path Extreme Low-Power Management with nanoWatt XLP™: Sleep mode: 100 nA, typical Watchdog Timer: 500 nA, typical Timer1 Oscillator: 500 nA @ typical 32 kHz Flexible Oscillator Structure Precision 16 MHz internal oscillator block Four Crystal modes up to 64 MHz Two external Clock modes up to 64 MHz 4X Phase Lock Loop (PLL) Secondary oscillator using Timer1 @ 32 kHz Two-Speed Oscillator Start-up Special Microcontroller Features: Full 5.5V operation Low voltage option available for 1.8V-3.6V operation Self-reprogrammable under software control Power-on Reset (POR), Power-up Timer (PWRT) and Oscillator Start-up Timer (OST) Programmable Brown-out Reset (BOR) Analog Features: Analog-to-Digital Converter (ADC) module : 10-bit Resolution Programmable High/Low Voltage Detection (PLVD) module Charge Time Measurement Unit (CTMU) for mTouch™ support Analog comparator module Voltage reference module Peripheral Features: 24/35 I/O pins and 1 input-only pin Three external interrupt pins Up to seven Timer modules Up to two Capture/Compare/PWM (CCP) modules Up to three Enhanced Capture/Compare/PWM (ECCP) modules Two Master Synchronous Serial Port (MSSP) modules Two Enhanced Universal Synchronous Asynchronous Receiver Transmitter modules (EUSART)
$5.03
PIC18F Series 32 KB Flash 2 kB RAM 48 MHz 8-Bit Microcontroller - SPDIP-28
COST PER PIECE The PIC18F25K50-I/SP is a high-performance PIC18 family 8-bit powerful (200 nanosecond instruction execution) yet easy-to-program CMOS flash based Microcontroller packs powerful PIC®(RISC) architecture with up to 16 MIPS of processing power with benchmark nanoWatt XLP extreme low power consumption. This product offer all of the advantages of the well recognized high-performance x16 architecture with standardized features including 32kB of addressable program memory size, 2048bytes of data memory size, 25 general-purpose I/O pins, two comparators, 14-channel 10-bit analog-to-digital (A/D) converter and one 5-bit digital-to-analog (D/A) converter. This device operates at a maximum frequency of 48MHz wide operating voltage of 1.8 to 5.5V. 83 (16-bit wide) powerful C-optimized 32 level hardware stack 1 (8-bit) file select register Integrated 8x8 hardware multiply Programmable brown-out reset (BOR) Programmable low voltage detection 16MHz internal oscillator Watch dog timer (WDT) Internal voltage reference (Bandgap) Charge time measurement unit (CTMU) Two 8-bit digital timers Two 16-bit digital timers 1x Capture/Compare/PWM (CCP) 1x Enhanced Capture/Compare/PWM (ECCP) full-speed USB 2.0 Local interconnect network (LIN) 14x Capacitive touch channels In-Circuit Serial Programming™ (ICSP™) 256bytes of EEPROM data memory Applications: Industrial, Automotive, Consumer Electronics, Motor Drive & Control, Lighting, Medical, Security Warnings: Market demand for this product has caused an extension in leadtimes. Delivery dates may fluctuate. Product exempt from discounts.
$4.69
PIC18F Series 32 KB Flash 1.5 kB RAM 40 MHz 8-Bit Microcontroller - SDIP-28
COST PER PIECE PIC18F2520-I/SP is a 8-bit Microcontroller has 32 KBytes of Flash Program Memory with 25 I/O's. It's maximum CPU speed is 40 MHz with an operating voltage range of 2 V - 5.5 V in a 28-Pin PDIP package. It has an industrial temperature ranges from (-40°C to +85°C).PIC18F2520 is ideal for applications requiring cost-effective, low-power solutions with a robust peripheral set in a small package. PIC18F having low power, high performance 8-bit MCU with integrated full-speed USB 2.0 and peripheral flexibility. Features: CPU:Up to 10 MIPS performanceC compiler optimized RISC architecture8 x 8 Single Cycle Hardware MultiplySystem:Internal oscillator support - 31 kHz to 8 MHz, up to 32 MHz with 4X PLLFail-Safe Clock Monitor – allows safe shutdown if clock failsWatchdog Timer with separate RC oscillatorWide operating Voltage range; 2.0 V to 5.5 VNanoWatt Power Managed Modes:Run, Idle and Sleep modesIdle mode currents down to 5.8 uA typicalSleep mode currents down to 0.1 uA typicalAnalog Features: 10-bit ADC, 13 channels100K samples per secondProgrammable Low Voltage Detection ModuleProgrammable Brown-out Reset moduleTwo Analog comparators with input multiplexingEUSART module including LIN bus supportFour Timer ModulesUp to 5 PWM outputsUp to 2 Capture / Compare / PWM(CCP) module
$7.45
PIC18F Series 16 kB Flash 768 B RAM 48 MHz 8-Bit Microcontroller - QFN-20
COST PER PIECE This device features a full speed USB 2.0 compliant interface that can automatically change clock sources and power levels upon connection to a host, making it an exceptional device for battery-powered applications. Features: C Compiler optimized architecture Self-programmable under software control Support for Interrupt Priority Levels 8x8 Single-Cycle Hardware Multiplier Enhanced Watchdog Timer with a programmable period USB v2.0 compliant interface Automatic detection of physical connection to USB host 256-byte Dual Access RAM Can be internally clocked up to 48 MHz Dual Capture/Compare/PWM interfaces Up to 5 PWM Outputs Master I2C/SPI Interface Supports all modes of 3-wire SPI Enhanced Addressable USART Module Supports RS-485, RS-232, and LIN 2.0 1.8 to 5.6V Operating Range Software Programmable Brown-out Reset feature Four power-managed operating modes Two-speed clock startup option
$3.43
PIC18F Series 16 kB Flash 512 B RAM 64 MHz 8-Bit Microcontroller - SOIC-20
COST PER PIECE The PIC18F14K22-I/SO is a 8-bit Microcontroller has 16 Kbytes of Flash Program Memory in a 20 Pin SOIC package. It has an industrial temperature ranges from (-40°C to +85°C). The PIC18F1XK22 family devices offer all of the advantages of the well recognized PIC18F High Performance MCUs; 8-bit, C compiler optimized architecture and an industry leading peripheral set now available in a low pin-count option. Features: C Compiler optimized architecture256 bytes data EEPROMLinear program memory addressing to 16 KbytesLinear data memory addressing to 512 bytesExtreme Low-Power ManagementPIC18LF1XK22 with nanoWatt XLP™ TechnologySleep mode: 50 nA, typicalWatchdog Timer: 600 nA, typicalTwo-Speed Oscillator Start-upOperating voltage 1.8 V- 5.5 VSelf-reprogrammable under software control
$3.18
PIC18F Series 4 kB Flash 256 B RAM 40 MHz 8-Bit Microcontroller - PDIP-18
COST PER PIECE The PIC18F1320-I/P is a part of PIC18F series 8-bit Microcontroller. It has 8 Kbytes of Flash Program Memory in a 18 Pin PDIP package. It has an industrial temperature ranges from -40°C to +85°C.The PIC18F1320 microcontroller has nanoWatt Technology, which features six enhanced power-managed "software controlled" modes, power consumption as low as 0.1 microamps in standby mode and a wide operating voltage range from 2 to 5.5 volts which makes this device ideal for battery managed applications. This device also encompasses a new low-current watchdog timer, a 2-speed start-up from a reset or sleep mode and a new fail-safe clock monitor that is used to detect an external clock failure. Features: 'C'compiler friendly development environment128 bytes of EEPROMSelf-programming, an ICDcapture/compare/PWM functions7 channels of 10-bit Analog-to-Digital (A/D) converterAddressable Universal Asynchronous Receiver Transmitter (AUSART)Internal OscillatorSelf Programming
$4.74
PIC18F Series 4 kB Flash 256 B RAM 40 MHz 8-Bit Microcontroller - SOIC-18
COST PER PIECE PIC18F1220-I/SO is a 8-bit Microcontroller has 4 Kbytes of Flash Program Memory in a 18 Pin SOIC package. It has an industrial temperature ranges from (-40°C to +85°C). PIC18F1220 microcontroller has nanoWatt Technology, which features six enhanced power-managed "software controlled" modes, power consumption as low as 0.1 microamps in standby mode and a wide operating voltage range from 2 to 5.5 volts which makes this device ideal for battery managed applications. This device also encompasses a new low-current watchdog timer, a 2-speed start-up from a reset or sleep mode and a new fail-safe clock monitor that is used to detect an external clock failure. Features: 'C'compiler friendly development environment Self-programming, an ICD capture/compare/PWM functions 7 channels of 10-bit Analog-to-Digital (A/D) converter Addressable Universal Asynchronous Receiver Transmitter (AUSART) Internal Oscillator Self Programming
$3.95
PIC16F Series 7 kB Flash 256 B RAM 20 MHz 8-Bit Microcontroller - SDIP-28
COST PER PIECE The PIC16F913-I/SP 8-bit Microcontroller has 7 K of Flash Program Memory with 25 I/O's. It's maximum CPU speed is 20 MHz with an operating voltage range of 2 V - 5.5 V in a 28-Pin PDIP package. It has an industrial temperature range of -40°C to +85°C and is lead free.The PIC16F913-I/SP 13-bit program counter capable of addressing a 4 k x 14 program memory space for the PIC16F913/914 (0000h-0FFFh) and an 8 k x 14 program memory space for the PIC16F916/917 (0000h-1FFFh). Accessing a location above the memory boundaries for the PIC16F913 and PIC16F914 will cause a wrap around within the first 4 k x 14 space. The Reset vector is at 0000h and the interrupt vector is at 0004h. Features: Up to 60 LCD segments7 KB Flash Program Memory256 B Data EEPROMInternal 32 kHz to 8 MHz oscillatorLow-power nanoWatt Technology25 mA Source/Sink current I/OTwo 8-bit Timer (TMR0/TMR2)One 16-bit Timer (TMR1)Extended Watchdog Timer (EWDT)Wide Operating Voltage (2.0 V – 5.5 V)Brown-Out Reset (BOR) with Software ControlIn Circuit Serial Programming (ICSP)Programmable Low Voltage Detect (PLVD)Wake on changeI2C, SPI, AUSART
$4.88
PIC16F Series 14 kB Flash 368 B RAM 20 MHz 8-Bit Microcontroller - PDIP-40
COST PER PIECE The PIC16F887-I/P 8-bit Microcontroller has 14 K of Flash Program Memory with 25 I/O's. It's maximum CPU speed is 20 MHz with an operating voltage range of 2 V - 5.5 V in a 28-Pin SSOP package. It has an industrial temperature range of -40°C to +85°C and is lead free.This powerful yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip's powerful PIC® architecture into a 28 pin package. The PIC16F882 features 128 bytes of EEPROM data memory, self programming, an ICD, 2 Comparators, 11 channels of 10-bit Analog-to-Digital (A/D) converter, 1 capture/compare/PWM and 1 Enhanced capture/compare/PWM functions, a synchronous serial port that can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus and an Enhanced Universal Asynchronous Receiver Transmitter (EUSART). Features: Precision Internal Oscillator:Factory calibrated to ±1%Software selectable frequency range of 8 MHz to 32 kHzSoftware tunableTwo-Speed Start-Up modeFail-safe clock monitoring for critical applicationsClock mode switching during operation for low-power operationPower-Saving Sleep modePower-on Reset (POR)Selectable Brown-out Reset (BOR) voltageExtended Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operationIn-Circuit Serial Programming™ (ICSP™) via two pinsIn-Circuit Debug (ICD) via two pinsSelf-reprogrammable under software controlProgrammable code protectionCapture/Compare/PWM (CCP) moduleEnhanced Capture/Compare/PWM (ECCP) module with auto-shutdown and PWM steeringMaster Synchronous Serial Port (MSSP) module SPI™ mode, I2C™ mode with address mask capability Applications: Analog/integrated level applicationsAutomotiveIndustrialAppliancesConsumer applications
$4.13
PIC16F Series 14 kB Flash 368 B RAM 20 MHz 8-Bit Microcontroller - SDIP-28
COST PER PIECE Microchip provides solutions for the entire performance range of 8-bit, 16-bit, and 32-bit microcontrollers.The 8-bit PIC® microcontroller solutions feature a powerful architecture, flexible memory technologies, comprehensive easy-to-use development tools, comprehensive application notes, complete technical documentation and post design-in support through a worldwide sales and distribution network. Microchip is committed to easy migration across product families, providing seamless program memory expansion, pin compatibility, and a unified development environment for all products.This powerful yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip's powerful PIC® architecture into a 28 pin package.The PIC16F886 features 256 bytes of EEPROM data memory, self programming, an ICD, 2 Comparators, 11 channels of 10-bit Analog-to-Digital (A/D) converter, 1 capture/compare/PWM and 1 Enhanced capture/compare/PWM functions, a synchronous serial port that can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus and an Enhanced Universal Asynchronous Receiver Transmitter (EUSART). All of these features make it ideal for more advanced level A/D applications in automotive, industrial, appliances or consumer applications.The PIC16F886-I/SP 8-bit Microcontroller has 14 K of Flash Program Memory with 25 I/O's. It's maximum CPU speed is 20 MHz with an operating voltage range of 2 V - 5.5 V in a 28-Pin PDIP package. It has an industrial temperature range of -40°C to +85°C and is lead free. Features: Precision Internal Oscillator:Factory calibrated to ±1%.Software selectable frequency range of 8 MHz to 32 kHz.Software tunable.Two-Speed Start-Up mode.Fail-safe clock monitoring for criticalapplications.Clock mode switching during operation for low-power operation.Power-Saving Sleep mode.Power-on Reset (POR).Selectable Brown-out Reset (BOR) voltage.Extended Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation.In-Circuit Serial Programming™ (ICSP™) via two pins.In-Circuit Debug (ICD) via two pins.High-endurance Flash/EEPROM cell:100,000 erase/write cycle enhanced Flash program memory, typica.1,000,000 erase/write cycle data EEPROM memory, typical.Data EEPROM retention > 40 years.Self-reprogrammable under software control.Programmable code protection.
$3.84
PIC16F Series 14 kB Flash 368 B RAM 20 MHz 8-Bit Microcontroller - SOIC-28
COST PER PIECE The PIC16F886 series of 8-bit Microcontroller has 7 K of Flash Program Memory with 25 I/O's. It's maximum CPU speed is 20 MHz with an operating voltage range of 2 V - 5.5 V in a 28-Pin SOIC package. It has an industrial temperature range of -40°C to +85°C and is lead free.This powerful yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip's powerful PIC® architecture into a 28 pin package.The PIC16F882 features 128 bytes of EEPROM data memory, self programming, an ICD, 2 Comparators, 11 channels of 10-bit Analog-to-Digital (A/D) converter, 1 capture/compare/PWM and 1 Enhanced capture/compare/PWM functions, a synchronous serial port that can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus and an Enhanced Universal Asynchronous Receiver Transmitter (EUSART). Features: Precision Internal Oscillator:Factory calibrated to ±1%Software selectable frequency range of 8 MHz to 32 kHzSoftware tunableTwo-Speed Start-Up modeFail-safe clock monitoring for critical applicationsClock mode switching during operation for low-power operationPower-Saving Sleep modePower-on Reset (POR)Selectable Brown-out Reset (BOR) voltageExtended Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operationIn-Circuit Serial Programming™ (ICSP™) via two pinsIn-Circuit Debug (ICD) via two pinsSelf-reprogrammable under software controlProgrammable code protectionCapture/Compare/PWM (CCP) moduleEnhanced Capture/Compare/PWM (ECCP) module with auto-shutdown and PWM steeringMaster Synchronous Serial Port (MSSP) module SPI™ mode, I2C™ mode with address mask capability Applications: Analog/integrated level applicationsAutomotiveIndustrialAppliancesConsumer applications
$3.37
PIC16F Series 3.5 kB Flash 128 B RAM 20 MHz 8-Bit Microcontroller - SDIP-28
COST PER PIECE The PIC16F883 series of 8-bit Microcontroller has 7 K of Flash Program Memory with 25 I/O's. It's maximum CPU speed is 20 MHz with an operating voltage range of 2 V - 5.5 V in a 28-Pin SOIC package. It has an industrial temperature range of -40°C to +85°C and is lead free.This powerful yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip's powerful PIC® architecture into a 28 pin package.The PIC16F882 features 128 bytes of EEPROM data memory, self programming, an ICD, 2 Comparators, 11 channels of 10-bit Analog-to-Digital (A/D) converter, 1 capture/compare/PWM and 1 Enhanced capture/compare/PWM functions, a synchronous serial port that can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus and an Enhanced Universal Asynchronous Receiver Transmitter (EUSART). Features: Precision Internal Oscillator:Factory calibrated to ±1%Software selectable frequency range of 8 MHz to 32 kHzSoftware tunableTwo-Speed Start-Up modeFail-safe clock monitoring for critical applicationsClock mode switching during operation for low-power operationPower-Saving Sleep modePower-on Reset (POR)Selectable Brown-out Reset (BOR) voltageExtended Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operationIn-Circuit Serial Programming™ (ICSP™) via two pinsIn-Circuit Debug (ICD) via two pinsSelf-reprogrammable under software controlProgrammable code protectionCapture/Compare/PWM (CCP) moduleEnhanced Capture/Compare/PWM (ECCP) module with auto-shutdown and PWM steeringMaster Synchronous Serial Port (MSSP) module SPI™ mode, I2C™ mode with address mask capability Applications: Analog/integrated level applicationsAutomotiveIndustrialAppliancesConsumer applications
$3.56
PIC16 Family PIC16F8XX Series Microcontrollers, PIC16, 20 MHz, 3.5 KB, 28 Pins
COST PER PIECE The PIC16F882-I/SP is a 8-bit CMOS Flash-based Microcontroller. The microcontroller features 128 bytes of EEPROM data memory, self programming, an ICD, 2 comparators, 11 channels of 10-bit Analogue-to-digital (A/D) converter, 1 capture/compare/PWM and 1 enhanced capture/compare/PWM functions, a synchronous serial port that can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus and an Enhanced Universal Asynchronous Receiver Transmitter (EUSART). The PIC16F882 devices have two timers that offer necessary delays on power-up. One is the Oscillator Start-up Timer (OST), intended to keep the chip in reset until the crystal oscillator is stable. The other is the Power-up Timer (PWRT), which provides a fixed delay of 64ms (nominal) on power-up only, designed to keep the part in reset while the power supply stabilizes.High-performance RISC CPUPower-saving sleep modePower-on reset (POR)Extended watchdog timer (WDT) with its own on-chip RC oscillator for reliable operationIn-Circuit Serial Programming™ (ICSP™) via two pinsIn-Circuit Debug (ICD) via two pinsSelf-reprogrammable under software controlProgrammable code protectionEnhanced capture/compare/PWM (ECCP) module with auto-shutdown and PWM steeringMultiplexed master clear with pull-up/input pin Applications: Automotive, Industrial, Consumer ElectronicsWarningsMarket demand for this product has caused an extension in leadtimes. Delivery dates may fluctuate. Product exempt from discounts.
$3.22
PIC16F Series 14 kB Flash 368 B RAM 20 MHz 8-Bit Microcontroller - TQFP-44
COST PER PIECE The PIC16F877A series of 8-bit Microcontroller has 7 K of Flash Program Memory with 33 I/O's. It's maximum CPU speed is 20 MHz with an operating voltage range of 2 V - 5.5 V in a 44-Pin TQFP package. It has an extended temperature range of -40°C to +125°C and is lead free.This powerful (200 nanosecond instruction execution) yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip's powerful PIC® architecture into an 40- or 44-pin package and is upwards compatible with the PIC16C5X, PIC12CXXX and PIC16C7X devices. PIC16F877 features 256 bytes of EEPROM data memory, self programming, an ICD, 8 channels of 10-bit Analog-to-Digital (A/D) converter, 2 additional timers, 2 capture/compare/PWM functions, the synchronous serial port can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus and a Universal Asynchronous Receiver Transmitter (USART). All of these features make it ideal for more. Features: Precision Internal Oscillator:Factory calibrated to ±1%Software selectable frequency range of 8 MHz to 32 kHzSoftware tunableTwo-Speed Start-Up modeFail-safe clock monitoring for critical applicationsClock mode switching during operation for low-power operationPower-Saving Sleep modePower-on Reset (POR)Selectable Brown-out Reset (BOR) voltageExtended Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operationIn-Circuit Serial Programming™ (ICSP™) via two pinsIn-Circuit Debug (ICD) via two pinsHigh-endurance Flash/EEPROM cell:100,000 erase/write cycle enhanced Flash program memory, typical1,000,000 erase/write cycle data EEPROM memory, typicalData EEPROM retention > 40 yearsSelf-reprogrammable under software controlProgrammable code protection Applications: Advanced level A/D applicationsAutomotiveIndustrialAppliancesConsumer applications.
$8.69
PIC16F Series 7 kB Flash 192 B RAM 20 MHz 8-Bit Microcontroller - SDIP-28
COST PER PIECE The PIC16F873A series 8-bit Microcontroller has 7 K of Flash Program Memory with 22 I/O's. It's maximum CPU speed is 20 MHz with an operating voltage range of 2 V - 5.5 V in a 28-Pin QFN package. It has an industrial temperature range of -40°C to +85°C and is lead free.This powerful (200 nanosecond instruction execution) yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip's powerful PIC® architecture into an 28-pin package and is upwards compatible with the PIC16C5X, PIC12CXXX and PIC16C7X devices. The PIC16F873A features 128 bytes of EEPROM data memory, self programming, an ICD, 2 Comparators, 5 channels of 10-bit Analog-to-Digital (A/D) converter, the synchronous serial port can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus and a Universal Asynchronous Receiver Transmitter (USART). All of these features make it ideal for more. Features: 2 PWM 10-bit128 Bytes EEPROM data memoryICD25 mA sink/source per I/OSelf Programming Applications: Advanced level A/D applicationsAutomotiveIndustrialAppliancesConsumer applications
$7.41
PIC16F Series 3.5 kB Flash 128 B RAM 20 MHz 8-Bit Microcontroller - SDIP-28
COST PER PIECE The PIC16F872-I/SP 8-bit Microcontroller has 3.5 K of Flash Program Memory with 22 I/O's. It's maximum CPU speed is 20 MHz with an operating voltage range of 2 V - 5.5 V in a 28-Pin PDIP package. It has an industrial temperature range of -40°C to +85°C and is lead free.This powerful (200 nanosecond instruction execution) yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip's powerful PIC® architecture into an 28-pin package and is upwards compatible with the PIC16C5X, PIC12CXXX and PIC16C7X devices. The PIC16F872 features 64 bytes of EEPROM data memory, self programming, an ICD, 5 channels of 10-bit Analog-to-Digital (A/D) converter, 2 additional timers, a capture/compare/PWM functions and the synchronous serial port can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus. Features: 1 PWM 10-bit64 Bytes EEPROM data memoryICD25 mA sink/source per I/OSelf Programming Applications: advanced level A/D applicationAutomotiveIndustrialAppliancesConsumer applications
$5.23
PIC 16F Microcontroller 8-bit 4MHz 1,75KB FLASH DIP18 PIC 16 F 84 A-04/P
COST PER PIECE This powerful 200ns instruction execution yet easy-to-program CMOS Flash/EEPROM-based 8-bit microcontroller packs Microchip's powerful PIC architecture into an 18-pin package. The same device can be used for prototyping and production and the end application can be easily updated without removing the device from the end product via the ICSP. Only 35 single word instructions to learn, all instructions single-cycle except for program branches which are two-cycle, 14-bit wide instruction words, 8-bit wide data bytes, 15 special function hardware registers, eight-level deep hardware stack, direct, indirect and relative addressing modes. Easily adapted for automotive, industrial, appliances low power remote sensors, electronic locks and security applications. Supply voltage 2V to 6V Flash memory 1.75KB EEPROM memory 64Bytes SRAM data memory 68Bytes 13 I/O pins 1 timer Clock speed 4MHz 18-DIP case Family PIC16F84A Clock Speed 4MHz EEPROM Memory 64Bytes SRAM Data Memory 68Bytes Flash Memory 1.75KB Supply Voltage 2 to 5.5V Package/Case DIL-18
$6.36
PIC16F Series 3.5 kB Flash 256 B RAM 20 MHz 8-Bit Microcontroller - SOIC-18
COST PER PIECE The PIC16F819 features 8MHz internal oscillator, 256 bytes of EEPROM data memory, a capture/compare/PWM, a synchronous serial port that can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus and 5 channels of 10-bit Analog-to-Digital (A/D) converter that make it ideal for advantage analog / integrated level applications.This powerful (200 nanosecond instruction execution) yet easy–to-program (only 35 single word instructions) CMOS Flash-based 8-bit microcontroller packs Microchip’s powerful PIC® architecture into an 18-pin package and is upwards compatible with the PIC16C7x, PIC16C62xA, PIC16C5X and PIC12CXXX devices. Features: 1 PWM 10-bit8 MHz Internal OscillatorICD256 bytes of EEPROM data memoryCapture/Compare Applications: AutomotiveIndustrialAppliances Consumer applications.
$3.59
PIC16 Family PIC16F7XX Series Microcontrollers, PIC16, 20 MHz, 3.5 KB, 18 Pins
COST PER PIECE The PIC16F716-I/P is a 8-bit Flash-based Microcontroller. This powerful (200 nanosecond instruction execution) yet easy-to-program (only 35 single word instructions) CMOS flash-based microcontroller is upwards compatible with the PIC16C5X and PIC12FXXX devices. The PIC16F716 features 4 channels of 8-bit Analogue-to-digital (A/D) converter with 2 additional timers and a enhanced capture/compare/PWM function. The Analogue-to-digital Converter (ADC) allows conversion of an analogue input signal to a 8-bit binary representation of that signal. This device uses analogue inputs, which are multiplexed into a single sample and hold circuit. The output of the sample and hold is connected to the input of the converter. The converter generates a 8-bit binary result via successive approximation and stores the conversion result into the ADC result register (ADRES).High-performance RISC CPUPower-on reset (POR)Power-up timer (PWRT) and oscillator start-up timer (OST)Watchdog timer (WDT) with its own on-chip RC oscillator for reliable operationProgrammable code protectionPower-saving sleep modeFully static designIn-Circuit Serial Programming™ (ICSP™) capability-40 to +85°C Temperature range (industrial) Applications: Automotive, Industrial, Consumer ElectronicsWarningsESD sensitive device, take proper precaution while handling the device. Market demand for this product has caused an extension in leadtimes. Delivery dates may fluctuate. Product exempt from discounts.
$1.90
PIC16F Series 1.75 kB Flash 64 B RAM 20 MHz 8-Bit Microcontroller - PDIP-14
COST PER PIECE The PIC16F630-I/P is part of PIC16F mid-range family with a 8-Bit Microcontroller. It can sustain standard temperature ranges from -40°C to +125°C and has 14 pin in PDIP package. This device is lead free.This powerful (200 nanosecond instruction execution) yet easy-to-program (only 35 single word instructions) CMOS Flash-based 8-bit microcontroller packs Microchip’s powerful PIC® MCU architecture into a 14-pin package and features 1 comparator and 128 bytes of EEPROM data memory.This device is easily adapted for automotive, industrial, appliances and consumer entry-level product applications that require field re-programmability. Features: High-Performance RISC CPU:Only 35 Instructions to LearnAll single-cycle instructions except branchesOperating Speed:DC – 20 MHz oscillator/clock inputDC – 200 ns instruction cycleSpecial Microcontroller Features:Internal and External Oscillator OptionsPrecision Internal 4 MHz oscillator factory calibrated to ±1%External Oscillator support for crystals and resonators5 μs wake-up from Sleep, 3.0 V, typicalPower-Saving Sleep modeWide Operating Voltage Range – 2.0 V to 5.5 VPeripheral Features:12 I/O Pins with Individual Direction ControlHigh Current Sink/Source for Direct LED DriveAnalog Comparator module with:One analog comparatorProgrammable on-chip comparator voltage reference (CVREF) moduleProgrammable input multiplexing from device inputsComparator output is externally accessible
$2.28
PIC16 Family PIC16F6XX Series Microcontrollers, PIC16, 20 MHz, 3.5 KB, 18 Pins
COST PER PIECE The PIC16F628A-I/P is an 18 pin, flash based, 8 bit microcontroller. This device employs an advanced RISC architecture. The PIC16F628A-I/P has enhanced core features, an eight level deep stack, and multiple internal and external interrupt sources. The separate instruction and data buses of the Harvard architecture allow a 14 bit wide instruction word with the separate 8 bit wide data. The two stage instruction pipeline allows all instructions to execute in a single cycle, except for program branches (which require two cycles). A total of 35 instructions (reduced instruction set) are available, complemented by a large register set.Interrupt Capability8 level deep hardware stackDirect, indirect, and relative addressing modesInternal and external oscillator optionsPower saving sleep modeProgrammable weak pull-ups on PORTBMultiplexed master clear/input pinWatchdog timer with independent oscillator for reliable operationLow voltage programmingIn circuit serial programmingProgrammable code protectionBrown-out ResetPower-on ResetPower-up timer and Oscillator start-up timer1,000,000 write EEPROM endurance40 year data retentionDual speed internal oscillatorRun-time selectable between 4MHz and 48kHz4µs wake-up from Sleep, 3.0V, typ.16 I/O pins with individual direction control Applications: Clock & Timing, Embedded Design & Development, Imaging, Video & Vision, Industrial, Motor Drive & Control, Multimedia, Portable Devices, Sensing & Instrumentation, Wireless
$3.24
PIC16 Family PIC16F6XX Series Microcontrollers, PIC16, 20 MHz, 1.75 KB, 18 Pins
COST PER PIECE The PIC16F627A-I/P is a 8-bit fully-static Flash-based CMOS Microcontroller. The PIC16F627A features 4MHz internal oscillator, 128 bytes of EEPROM data memory, a capture/compare/PWM, a USART, 2 comparators and a programmable voltage reference. The PIC16F627A have enhanced core features, an eight-level deep stack and multiple internal and external interrupt sources. The separate instruction and data buses of the Harvard architecture allow a 14-bit wide instruction word with the separate 8-bit wide data. The two-stage instruction pipeline allows all instructions to execute in a single cycle, except for program branches (which require two cycles). A total of 35 instructions (reduced instruction set) are available, complemented by a large register set. The PIC16F627A device have integrated features to reduce external components, enhancing system reliability and reducing power consumption. The PIC16F62X series fits in applications ranging from battery chargers to low power remote sensors.Low voltage programmingLow speed clock mode4MHz Internal oscillatorOn-chip voltage referencePower-saving sleep modeProgrammable weak pull-ups on port-BMultiplexed master clear/input-pinWatchdog timer with independent oscillator for reliable operationLow-voltage programmingIn-Circuit Serial Programming™ (via two pins)Programmable code protectionBrown-out reset and power-on resetPower-up timer and oscillator start-up timerIndustrial and extended temperature rangeSupplier's original packaging: Tube Applications: Power Management, Sensing & Instrumentation, Automotive, Industrial, Consumer ElectronicsWarningsESD sensitive device, take proper precaution while handling the device. Market demand for this product has caused an extension in leadtimes. Delivery dates may fluctuate. Product exempt from discounts.
$2.87
PIC16F Series 1.75 kB Flash 224 B RAM 20 MHz 8-Bit Microcontroller - PDIP-18
COST PER PIECE PIC16F627-04/P is part of PIC16F mid-range family with a 8-Bit Microcontroller. It can sustain standard temperature ranges from -40°C to +85°C and has 18 pin in PDIP package. This device is lead free.The high performance of the PIC16F62X family can be attributed to a number of architectural features commonly found in RISC microprocessors. To begin with, the PIC16F62X uses a Harvard architecture, in which, program and data are accessed from separate memories using separate buses. This improves bandwidth over traditional Von Neumann architecture where program and data are fetched from the same memory.Separating program and data memory further allows instructions to be sized differently than 8-bit wide data word. Instruction opcodes are 14-bits wide making it possible to have all single-word instructions. Features: Low voltage programminglow speed Clock modeProgrammable BOR4 MHz internal RC oscillatoron-chip voltage reference128 bytes of EEPROM Data Memory
$3.61
PIC16F Series 3.5 KB Flash 128 B RAM 20 MHz 8-Bit Microcontroller - PDIP-14
COST PER PIECE PIC16F616-I/P is part of PIC16F mid-range family with a 8-Bit Microcontroller. It can sustain standard temperature ranges from -40°C to +150°C and has 14 pin in PDIP package. This device is lead free. Features: Flash Program MemoryInternal 4/8 MHz oscillatorComparator with hysterisis (user configurable)Mid-Range core with 35 Instruction, 8 Stack Levels25 mA Source/Sink current I/OTwo 8-bit Timer (TMR0/TMR2)One 16-bit Timer (TMR1)Watchdog Timer (WDT)Enhanced Power-On/Off-ResetBrown-Out Reset (BOR)In Circuit Serial Programming (ICSP)Enhanced Capture Compare PWM (Pulse Width Modulation)Wide Operating Voltage (2.0 V – 5.5 V)High Voltage PIC16HV616 variant (2.0 V – User Defined) with internal shunt regulator
$2.05
PIC16F Series 3 kB Flash 72 B RAM 20 MHz 8-Bit Microcontroller - SPDIP-28
COST PER PIECE PIC16F57-I/SP is part of PIC16F mid-range family with a 8-Bit Microcontroller. It can sustain standard temperature ranges from -40°C to +125°C and has 28 pin in SPDIP package. This device is lead free.This powerful (200 nanosecond instruction execution) yet easy-to-program (only 33 single-word instructions) FLASH-based 8-bit microcontroller packs Microchip’s powerful PICmicro® architecture into an 18-pin package. Easily adapted for automotive, industrial, appliances and consumer entry-level product applications. Features: 28-pin packagingBaseline Core with 33 Instructions, 2 Stack LevelsAll single-cycle Instructions except for program branches which are two cycles12-bit wide instructions8-bit wide data path25 mA source/sink current I/OLow power (100 nA) sleep currentOne 8-bit timer (TMR0)Watchdog timer (WDT)In-Circuit Serial Programming™In-Circuit debugging supportProgrammable code protection
$1.60
PIC16F Series 3 kB Flash 72 B RAM 20 MHz 8-Bit Microcontroller - PDIP-28
COST PER PIECE PIC16F57-I/P is part of PIC16F mid-range family with a 8-Bit Microcontroller. It can sustain standard temperature ranges from -40°C to +125°C and has 28 pin in PDIP package. This device is lead free.This powerful (200 nanosecond instruction execution) yet easy-to-program (only 33 single-word instructions) FLASH-based 8-bit microcontroller packs Microchip’s powerful PICmicro® architecture into an 18-pin package. Easily adapted for automotive, industrial, appliances and consumer entry-level product applications. Features: 28-pin packagingBaseline Core with 33 Instructions, 2 Stack LevelsAll single-cycle Instructions except for program branches which are two cycles12-bit wide instructions8-bit wide data path25 mA source/sink current I/OLow power (100 nA) sleep currentOne 8-bit timer (TMR0)Watchdog timer (WDT)In-Circuit Serial Programming™In-Circuit debugging supportProgrammable code protection
$1.60
PIC16F Series 768 B Flash 25 B RAM 20 MHz 8-Bit Microcontroller- PDIP-18
COST PER PIECE PIC16F54-I/P is part of PIC16F mid-range family with a 8-Bit Microcontroller. It can sustain standard temperature ranges from -40°C to +125°C and has 18 pin in PDIP package. This device is lead free.This powerful (200 nanosecond instruction execution) yet easy-to-program (only 33 single-word instructions) FLASH-based 8-bit microcontroller packs Microchip’s powerful PICmicro® architecture into an 18-pin package. Easily adapted for automotive, industrial, appliances and consumer entry-level product applications. Features: 18-pin packagingBaseline Core with 33 Instructions, 2 Stack LevelsAll single-cycle Instructions except for program branches which are two cycles12-bit wide instructions8-bit wide data path25 mA source/sink current I/OLow power (100 nA) sleep currentOne 8-bit timer (TMR0)Watchdog timer (WDT)In-Circuit Serial Programming™In-Circuit debugging supportProgrammable code protection
$1.05
You have seen 48 out of 69 products